他由既有的電源驅動，也可以采用汽油發電機發電供應，一個3Kw的發電機可以驅動4個電動搗固鎬，可以同時對線路的2根鋼軌前后，左右同時搗固作業，

　　He driven by existing power, also can use gasoline generator power supply, a 3 kw generator can be driven four electric tamping picks, can at the same time, on line before, during and after the two rail around tamping homework at the same time,

　　電動搗固鎬使用方法與維護

　　Fourth, using method and maintenance

　　1、 檢查搗固架及電鎬的聯接螺栓是否正常，電源插頭、導線、插座聯接是否良好。

　　1, check the tamping and electric pick the connecting bolt is normal, whether the power plug, wire, socket connection is good.

　　2、 接通電源后空運轉一分鐘觀察是否正常。正常后方可投入工作。

　　2, idle running a minute observation after turning on the power supply is normal.Rear can work normally.

　　3、 距軌枕邊緣20-30mm下鎬，鎬板與軌枕面邊線成45o角，在進行搗固時漸放大角到80o左右，不斷抽鎬使道碴進入軌枕底。

　　3, 20-30 mm from edge of sleeper, pick, pick and sleeper surface edge Angle of 45 DHS, when making tamping gradually enlarge the Angle to about 80 DHS, constantly picks the ballast into the bottom of the sleeper.

　　4、使用時導線不要拉緊，避免出現斷線等現象。不用時導線繞好，放入通風的庫房保管，注意防潮，不得隨意扔摔本機具。

　　5、本機嚴禁在潮濕空氣和雨天作業。

　　4, when using wire do not tighten, avoid even the appearance of bolt, etc.Need not when wires with good, in a ventilated warehouse storage, note moistureproof, shall not be arbitrarily throw this machines and tools.

　　5, the machine is strictly prohibited in moist air and rain.

　　6、在連續作業中，要每周檢查絕緣電阻，保證絕緣電阻在大于7MΩ的情況下才可以上線作業。

　　6, in continuous operation, to check the insulation resistance per week, ensure insulation resistance in the case of more than 7 m Ω can online homework.

　　7、作業時累計500h應對鎬體和鎬頭進行重新組裝，清理在搗鎬作業時所產生的臟物。

　　7, total 500 h when working in the face of the picks body and reassemble the pickaxe, cleaning of dirt when working in dao picks.